Photoresist Step Coverage on 10–25 µm MEMS Structures and the Transition to Large Substrates
MEMS structures with topography in the 10–25 µm range are useful test cases for photoresist step coverage, but they do not define a universal operating window. Single-spin, multi-spin and spray approaches can produce different local thicknesses and development behavior. Ultrasonic Photoresist Coating should be evaluated at the critical corners and through the intended lithographic process. A separate scaling question arises for large panels or lenses: handling and area constraints may favor a non-spinning route, but that does not make ultrasonic spray the only possible coating method.
Read comparative experiments within their scope
The primary paper Improvement of Photoresist Film Coverage on High Topology Surface with Spray Coating Technique compares single-spin, multi-spin and direct spray methods on a specific approximately 14 µm structure. It reports better step coverage for the investigated spray process and discusses development behavior. That is useful experimental evidence for a particular material and geometry. It does not establish that every 10–25 µm MEMS structure will behave identically, or that every ultrasonic recipe avoids film lifting. The broader range requires its own representative test matrix.
Compare the minimum useful film, not only the average
A planar region, pillar top and convex corner can receive very different remaining thickness. An etch mask may fail at the thinnest location even if the average is high. Define the critical corner and the required residual film through the relevant downstream process. Measure multiple structures and substrate positions. Report both local thickness and roughness or defects. A thicker film everywhere is not always acceptable if it changes exposure, pattern dimensions or development access.
Understand single-spin and multi-spin tradeoffs
A single-spin process can be simple and well controlled for suitable surfaces, but its liquid redistribution may leave inadequate material over some raised features. Multiple coats can increase total thickness and alter the local profile, yet introduce solvent interaction, bake history and adhesion questions between layers. Those outcomes depend on the resist and sequence. Multi-spin should not be described as inevitably producing lift-off during development. Establish a feasible baseline and record its failure mode before using it in a comparative claim.
What spray deposition changes
Ultrasonic atomization creates droplets through mechanical vibration of a supplied liquid film. Guiding gas and motion distribute them over the structure. This changes the way material arrives compared with a central spin dispense. Film formation still depends on spreading, merging and solvent removal. Too much mobility can cause redistribution; too little can leave roughness or pinholes. Access to sidewalls and recesses also depends on geometry. A low-velocity mist is an enabling delivery characteristic, not proof of complete conformality.
Build a feature-level experiment
Include representative heights, widths, pitches and corner radii rather than only one nominal step. Record surface materials and any existing layers. Choose inspection at the planar area, raised top, corner and recess. Use methods suited to those locations and state sampling uncertainty. Keep the required mask or pattern function fixed even if each coating method needs a different recipe. If the resist or dilution changes, document the chemistry change so the result is not attributed solely to equipment.
Measure after development and transfer
Apply the intended bake, exposure and developer conditions, then inspect adhesion and remaining film at the critical positions. Development can reveal local stress or inadequate bonding that is absent in an as-coated image. If etch survival defines success, include a relevant etch test and record the remaining mask. If lift-off is the intended patterning process, distinguish successful removal from unintended film delamination during development. Using the same word for those different events can obscure the interpretation.
Control the coupled spray variables
Concentration, feed rate, stand-off, motion, path overlap and pass interval affect wet loading. Temperature and exhaust influence evaporation. Investigate them through a staged plan rather than increasing flow whenever a corner appears thin. Extra liquid can worsen recess accumulation or change roughness elsewhere. Verify actual substrate conditions under deposition, not only heater settings. Nozzle residue, gels and particles can change delivery, so cleaning, resist age and restart behavior belong in the process record.
Separate topographic capability from substrate size
A process that covers a small MEMS die does not automatically coat a large display panel uniformly. Larger areas introduce path length, overlap, support and temperature gradients. A lens adds curvature and changing stand-off. Define the accepted aperture and edge exclusion before inspection. Travel range is only one equipment requirement; fixture clearance, overshoot and handling access also matter. Reconfirm the complete process when transferring from a small test structure to a larger or differently shaped substrate.
Why large substrates can challenge spinning
Whether a substrate can be spun depends on the actual tool, mounting, clearance, mass, shape and mechanical tolerance. Rectangular samples are not categorically impossible to rotate, and larger radius does not imply one universal increase in required angular speed. At a given angular velocity, peripheral speed rises with radius, while mechanical and fluid behavior also change. Evaluate these constraints for the proposed system. A substrate may be impractical for the available spinner without being physically unspinnable under every possible arrangement.
Recognize alternative deposition routes
For some panels, meniscus, slot-die, blade or laminated-resist processes may be relevant. Their ability to coat deep topography, accept a particular chemistry or produce the intended pattern must be assessed separately. Their existence prevents a general claim that ultrasonic spraying is the only option for all large substrates. The useful selection question is which route meets local coverage, lithographic function, handling and cost requirements with a reproducible process. A route can be favored for one application without being universally exclusive.
Compare material use and contamination empirically
Include consumed resist solids, solvent, priming, purge, masks, cleaning and rejected substrates when comparing economics. A spray method can reduce some spin-off losses but still create overspray and maintenance consumption. Noncontact deposition does not eliminate particles or guarantee yield. Inspect incoming substrates and coated samples using equivalent conditions, then track defect sources. Avoid assigning a numerical saving or contamination reduction without a representative baseline. Accepted patterned output is often more informative than the capture fraction of a single pass.
Turn the comparison into a transfer package
Use independent runs and preparations, preserve individual data and retain failed samples. Document the selected resist, support, nozzle arrangement, path and thermal history together with exposure and development. Define acceptable operating ranges and how startup or restart material is qualified. If a result holds only for specific structures, state those limits. The most useful conclusion is a verified application envelope with known sensitivities, not a generalized claim of perfect coverage over every MEMS structure or large substrate.
Use separate confirmation specimens after choosing the best exploratory recipe. They should come from independent preparation and receive the complete intended handling and lithographic sequence. Do not count a recipe as confirmed merely because the original successful wafer can be measured repeatedly. If the next substrate format has different curvature, dimensions or feature density, identify the responses that must be checked again. This avoids treating scale-up as a simple multiplication of path length. The comparison remains credible when it reports a bounded advantage, a documented tradeoff or a failure that requires a different process route. Each outcome can guide engineering work without requiring an unsupported claim that one method always dominates.
Arrange a representative step-coverage trial
Qualified manufacturers and R&D teams are invited to contact Cheersonic at market2@cheersonic.com to discuss photoresist, catalyst coating or other functional coating projects and arrange a coating sample test. Review Cheersonic ultrasonic coating equipment solutions and provide the 10–25 µm feature drawings, substrate format, resist, critical corner requirement and downstream lithography sequence. A structured comparison can identify whether ultrasonic spraying offers a useful coverage advantage and what must be revalidated when moving to panels or lenses.

