ITO Films by Ultrasonic Spray Coating: Deposition, Thermal Treatment and Resistivity Measurement

An ITO film is not defined only by its chemical name. Indium tin oxide deposited from nanoparticles, a metal-salt precursor or another formulation can develop different connectivity, optical response and thermal requirements. Ultrasonic spray coating offers a liquid-deposition route, but it does not by itself guarantee conductivity. A credible process separates atomization, wet-film formation, solvent removal and any conversion or consolidation required by the selected material. Spray speed and resistivity must be established for that complete route.

Choose the ITO material pathway

A nanoparticle dispersion already contains oxide particles, yet interparticle contacts, ligands and binder can limit conduction. A precursor liquid requires formation of the intended oxide and removal of unwanted species. Spray pyrolysis deliberately couples aerosol delivery with thermal conversion and should not be confused with low-temperature deposition followed by a separate treatment. Define composition, tin content, solids and substrate before choosing a thermal schedule. A glass recipe is not automatically suitable for a heat-sensitive polymer film.

Use published evidence as context

The primary study A nanoparticle-mist deposition method: fabrication of high-performance ITO flexible thin films under atmospheric conditions, DOI 10.1038/s41598-021-90028-6, investigates an ultrasonic-mist nanoparticle route. It supports considering deposition and post-treatment together. Its results are not Cheersonic measurements or a universal recipe for another ITO ink. The practical workflow below defines project-specific tests rather than transferring a published resistivity or annealing atmosphere to an unspecified substrate.

Prepare and inspect the incoming liquid

Record the oxide or precursor identity, solvent, additives, concentration, preparation age and dispersion procedure. Agglomeration and settling can change delivered composition. A filter can remove unwanted particles but may also remove functional solids, so validate it. Check wetting and solvent compatibility on the actual substrate, including existing coatings. Keep uncoated and solvent-treated controls. Bubbles, dried residue and contamination can create local electrical breaks even where the film appears uniformly tinted.

Develop a deposition and speed window

Mechanical vibration at the ultrasonic head generates droplets; guiding gas and motion distribute them. Travel speed interacts with liquid flow, path spacing, capture and pass count. Consequently, there is no scientifically defensible universal speed for ITO. Estimate dry loading from captured solids per coated area, then calibrate with measured samples. If speed is increased while flow remains fixed, deposited loading may fall. Increasing flow in response can change wetting and drying, so test those effects rather than assuming exact compensation.

Map a representative footprint and overlap on the selected substrate. Excess wetting can pool particles or produce edge accumulation. Excessive evaporation can leave rough deposits with weak contact. Actual substrate temperature can differ from heater setpoint because of thermal contact and evaporative cooling. Record pass interval and final drying. Nozzle fouling can still occur through aggregates, gels or dried precursor, so include idle and restart samples when assessing repeatability over a realistic run.

Drying is not necessarily electrical consolidation

Removing solvent may leave an oxide-particle network that remains poorly connected. Depending on the formulation, later treatment may remove organics, improve contacts or complete oxide formation. Obtain material-specific guidance and verify changes experimentally. Thermal analysis and structural or chemical characterization can support schedule development. Do not prescribe a high-temperature or reactive-atmosphere treatment solely because it appeared in a paper. Substrate, furnace, gas handling and coating compatibility require their own engineering assessment.

Distinguish sheet resistance from resistivity

For a reasonably uniform continuous film, resistivity can be estimated as rho = Rs × t, where Rs is sheet resistance and t is thickness in consistent units. Sheet resistance is commonly reported in ohms per square; resistivity is a different quantity. A four-point method can reduce contact contributions, but measurement geometry and corrections still matter. A discontinuous or strongly nonuniform film may not support a simple bulk interpretation. Report the actual measurement and its limitations rather than calculating a misleading material constant.

Map resistance and thickness at corresponding locations and include optical transmittance or haze when transparency is required. A lower resistance achieved by a thicker film can trade against optical performance. Inspect cracks and evaluate adhesion after treatment. Flexible samples also need bending tests in a defined geometry and strain state. Report independent preparations and multiple specimens rather than only the most conductive region. Retain raw and treated results so the contribution of post-treatment remains visible.

Specify speed comparisons at a common accepted film state. A faster traverse that leaves a thinner layer is not evidence of higher accepted output if additional passes or annealing time are needed. Report deposition time, total passes and post-treatment separately. For electrical data, retain the individual resistance and thickness values used in the resistivity calculation, including units. This makes it possible to identify whether an apparent improvement reflects better particle connectivity, additional material or a measurement difference. Where the film is discontinuous, report that limitation instead of assigning a misleading bulk resistivity.

Arrange an ITO feasibility trial

Qualified manufacturers and R&D teams are invited to contact Cheersonic at market2@cheersonic.com to discuss ITO, catalyst coating or other functional coating projects and arrange a coating sample test. Review Cheersonic ultrasonic coating equipment solutions and provide ink route, substrate, thermal budget, optical target and electrical measurement plan. A trial can identify a useful speed, loading and treatment window without inventing conductivity figures or claiming that deposition alone completes the film.